- 您现在的位置：买卖IC网 > Sheet目录222 > DS1982-F5+ (Maxim Integrated)IBUTTON 1KBit ADD-ONLY F5
DS1982
A multidrop bus consists of a 1-Wire bus with multiple slaves attached. The 1-Wire bus has a maximum
data rate of 16.3kbps. If the bus master is also required to perform programming of the EPROM portions
of the DS1982, a programming supply capable of delivering up to 10 milliamps at 12 volts for 480 ? s is
required. The idle state for the 1-Wire bus is high. If, for any reason, a transaction needs to be suspended,
the bus MUST be left in the idle state if the transaction is to resume. If this does not occur and the bus is
left low for more than 120 ? s, one or more of the devices on the bus may be reset.
TRANSACTION SEQUENCE
The sequence for accessing the DS1982 via the 1-Wire port is as follows:
?
?
?
?
Initialization
ROM Function Command
Memory Function Command
Read/Write Memory/Status
INITIALIZATION
All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence
consists of a Reset Pulse transmitted by the bus master followed by a presence pulse(s) transmitted by the
slave(s).
The presence pulse lets the bus master know that the DS1982 is on the bus and is ready to operate. For
more details, see the “1-Wire Signaling” section.
ROM FUNCTION COMMANDS
Once the bus master has detected a presence, it can issue one of the four ROM function commands. All
ROM function commands are 8 bits long. A list of these commands follows (refer to flowchart in Figure
9):
Read ROM [33h]
This command allows the bus master to read the DS1982’s 8-bit family code, unique 48-bit serial
number, and 8-bit CRC. This command can be used only if there is a single DS1982 on the bus. If more
than one slave is present on the bus, a data collision will occur when all slaves try to transmit at the same
time (open drain will produce a wired-AND result).
Match ROM [55h]
The match ROM command, followed by a 64–bit ROM sequence, allows the bus master to address a
specific DS1982 on a multidrop bus. Only the DS1982 that exactly matches the 64-bit ROM sequence
will respond to the subsequent memory function command. All slaves that do not match the 64-bit ROM
sequence will wait for a Reset Pulse. This command can be used with a single or multiple devices on the
bus.
Page 15 of 24
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DS1985-F3+
IBUTTON 16KBit ADD-ONLY F3
DS1990A-F3+
IC IBUTTON SERIAL NUMBER F3
DS1990R-F5#
IBUTTON SERIAL NUMBER F5
DS1993L-F5+
IBUTTON MEMORY 4KBit F5
DS1995L-F5+
IBUTTON MEMORY 16KBit F5
DS1996L-F5+
IBUTTON MEMORY 64KBit F5
DS9092K#
KIT IBUTTON STARTER
DS9502P+T&R
DIODE ESD PROTECTION 6-TSOC
相关代理商/技术参数
DS1982-F5W+
功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1982U
制造商:未知厂家 制造商全称:未知厂家 功能描述:UniqueWare iButton
DS1982U-1118+A04
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1982U-1119+A04
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1982U-1151+A04
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1982U-A0B-116D+
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1982U-F3-1166+
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1982U-F3-1177+
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated